Skoda Fabia S2000 Evo Total Ypres Rally '11 (Job Log)

1
May 14, 2022
Panel-line engraved.
2
May 14, 2022
Classification by paint color.
3
May 14, 2022
The inner surface of the white shell parts was painted black.
4
May 14, 2022
L: Gloss White after White Surfacer.
R: Gloss Black for Chrom paint. and painted other color.
5
May 14, 2022
Masking.
6
May 14, 2022
Chrome paint.
7
May 14, 2022
The paint applied to the etching peels off easily. So I applied the Vallejo Mecha Primer.
8
May 14, 2022
Decal.
The side decals are made in one piece and take about each 2 hours, and a total of over 6 hours.
9
May 14, 2022
Tail lamp masking...
10
May 14, 2022
Clear coat.
11
May 14, 2022
Surface levelling.
12
May 14, 2022
Polishied with compound (Tamiya Fine)
But, It's a result I'm not happy with.
13
May 14, 2022
Finally, I did the polishing again the next day. (done)
14
May 14, 2022
Finally, I did the polishing again the next day. (done)
15
May 14, 2022
Paint to panel-line and deep mold.
16
May 14, 2022
Brush painted Flat, Satin black.
17
May 14, 2022
Brush painted Flat, Satin black.
18
May 14, 2022
I brushed it with this.
Best recommended~
19
May 14, 2022
Continuing brush painting.
20
May 14, 2022
Ext. lamps have been modified for easy attachment and removal using magnets.
Youtube Video
21
May 14, 2022
Ext. lamps have been modified for easy attachment and removal using magnets.
Youtube Video
22
May 14, 2022
Clear coat to front and rear emblem.
23
May 14, 2022
I cut out the silver foil sticker included in the Bandai Pokemon kit and used it.
24
May 14, 2022
All done. Ready to assemble.
25
May 16, 2022
This is similar to VANTA Black. (Acrylic)
26
May 16, 2022
I started assembling it according to the manual.
27
May 16, 2022
The wheels were so loose that they had to be fixed with glue.
28
May 16, 2022
It was the most complex structure of the steer wheels I've ever made.
29
May 16, 2022
The sheet decal on the floor was attached less closely to give a sense of volume.
I plan to detail up only the shoulder side of the seat belt.
30
May 16, 2022
assembling interior.
31
May 16, 2022
Inner side of door.
32
May 16, 2022
Easy detail-up spare tyre.
33
May 16, 2022
A spare tire must be attached before the roll cage is fully assembled.
34
May 16, 2022
Then just attach the roof side roll bar. But overall, it is not easy to assemble.
35
May 16, 2022
Easy detail-up for shoulder harness.
36
May 16, 2022
After putting on the sheet to the proper length...
37
May 16, 2022
Wrap it around the roll bar at the back and attach it.
38
May 16, 2022
I used Hasegawa sheet for sub tail lamp
39
May 16, 2022
But it was invisible from the outside.
It was a waste of time.
40
May 16, 2022
I attached the front and rear lamp covers and other trivial parts...
41
May 16, 2022
It was not easy to combine the shell with the lower plate.
42
May 16, 2022
The wing and the trivial parts on the roof were attached.
43
May 16, 2022
For the bonnet hook, etching was included in the kit, but the detail was simple, so I used an etching sold separately.
44
May 16, 2022
Finally, by assembling the extension lamp...
45
May 16, 2022
Finish
46
May 16, 2022
Finish
47
May 16, 2022
Finish

19 14 May 2022, 10:58

Dennis
Nice Progress 👍🏽 I usually brush paint window trims with vallejo flat black. Works also very well 😁

14 May 2022, 18:06

Kyle DeHart
Nice!

14 May 2022, 22:57

MS K
Thanks Dennis, Kyle DeHart.
@Dennis: Correct, The leveling is so good that even if you paint with a brush, no remained brush marks.

16 May 2022, 05:10

Dennis
yes! Another good thing is that if one messed up it can be easily removed with a damp cotton swab (i do that on my 2k clear surfaces with a little bit of tamiya X20A)...

17 May 2022, 11:00