Build log: 1/100 MG Freedom Gundam "1.75" 查看: 幻灯片 平铺 名单 1 September 6, 2020
The Freedom 2.0 kit. It has pretty much everything except the blue parts of the wings, along with the V-fin.
2 September 6, 2020
Torso assembled, this kit is very different from the Freedom 1.0 which is also assembled.
3 September 6, 2020
Upper torso assembled, you can see the additional detail of the newer kit.
4 September 6, 2020
Leg assembled. Unlike the original MG Freedom this does not have the splitting knee gimmick.
5 September 6, 2020
Most of the body assembled.
6 September 6, 2020
For the wings, I used two adapters that I 3D printed. First adapter joins the wings to the backpack, the second one allows me to use the Freedom 2.0 cannons on this kit.
7 September 6, 2020
So now for v-fin, I was considering multiple ways, first I made one with pla plate but it bends too easily at the ends.
8 September 6, 2020
I printed an adapter to use the 1.0 head on the 2.0 but I don't think it looks quite right so I went back to drawing board.
9 September 6, 2020
Used 3D printing to print out a v-fin I designed.
10 September 6, 2020
Compared to the pla-plate version, the V-fin is much stiffer, end points don't seem to blunt too badly.
11 September 6, 2020
Tried first prototype and mounted it on the head.
12 September 6, 2020
Adjusted the first prototype and added cuts to allow for the vertical portions to fit in.
13 September 6, 2020
Final v-fin design, I settled with this after 4 prototypes.
14 September 6, 2020
Compared to the old head, the newer head is more aggressive looking, which fits the aggressive design of Freedom 2.0.
15 September 6, 2020
Final v-fin design attached to body.
16 September 6, 2020
Primed to check layer lines and get rid of as much of it as possible.
17 September 6, 2020
Pla plate added at red sensor for better fit.
18 September 6, 2020
Cleaned up everything the best I can.
19 September 6, 2020
Preparing white parts for painting.
20 September 6, 2020
White parts primed and painted.
21 September 6, 2020
Testing color separation for white areas.
22 September 6, 2020
Using white primer to prime red parts for brighter finish.
23 September 6, 2020
Reds are a lot brighter with the use of white primer.
24 September 6, 2020
Shoulders almost done.
25 September 6, 2020
Head test fit.
26 September 6, 2020
Checking arm color separation.
27 September 6, 2020
Panel lining. Used grey for white areas, black for the darker areas.
28 September 6, 2020
Hips done.
29 September 6, 2020
Arms done.
30 September 6, 2020
Shoulders done with decals.
31 September 6, 2020
Upper torso done.
32 September 6, 2020
Testing out new light booth for shoots.
33 September 6, 2020
Feet done as well.
34 September 6, 2020
Attached the legs without the outer armor.
35 September 6, 2020
Body completed.
36 September 6, 2020
Railguns added.
37 September 6, 2020
Used two color seperation for wing areas.
38 September 6, 2020
Completed work. Dark areas are two toned: Midnight Blue and Black, while blue areas are two tone, with the use of Phytocyanate Blue and Cobalt Blue
39 September 6, 2020
With wings spread.
40 September 6, 2020
Front view.
41 September 6, 2020
Back view.
42 September 6, 2020
Close up view.
43 September 6, 2020
Wings spread.
评论 23 November 2024, 22:48 -
Album info Used 3D printing and wings from the older kit to combine into one complete product.
43 图片
1:100
已完成
所有相册 查看所有相册 »