Motormaster 查看: 幻灯片 平铺 名单 1 September 25, 2017
Sprues. Bottom left is de-chromed.
2 September 25, 2017
Who thought this was a good idea of attaching parts?
3 September 25, 2017
This kit is a bit older....
4 September 25, 2017
Like Kerry Cox says, remove the lines
5 September 28, 2017
Sand away!
6 September 28, 2017
This cannister is a bit too close to the holder.
7 September 28, 2017
Much better. Needs to be sanded a bit more.
8 October 5, 2017
Who thought this is a good idea of connecting the sprue to the part?
9 October 5, 2017
Luckily no damage done.
10 October 5, 2017
Mind the gap.
11 October 5, 2017
Mind the gap. This being an older snap tite kit, dry fitting is hard/tough/impossible.
12 October 5, 2017
After a lot of sanding, filling and more sanding....
13 October 5, 2017
These tanks seem acceptable.
14 October 15, 2017
Right original, left drilled. Better!
15 October 15, 2017
Just these two stacks took nearly 45 minutes to erase the seamlines.
16 October 21, 2017
Some more to sand.
17 18 October 21, 2017
Only light sand work needed
19 October 21, 2017
Fill the gap!
20 21 October 21, 2017
Drive shaft needed some attention
22 October 21, 2017
One of the antennae on the mirrors was broken.
23 October 21, 2017
Replaced them with 0.5mm rod
24 October 21, 2017
Only soft sanding along the edges.
25 October 21, 2017
This small piece neede a lot of sanding. Put it in the drill handle for extra grip.
26 27 28 October 21, 2017
Flash & seamlines...
29 October 21, 2017
Way better
30 October 21, 2017
Tiny stuff
31 October 21, 2017
The sides of the handles needed only scraping
32 October 21, 2017
tired of sanding red pieces, turned attention to black pieces. Same here 🙁
33 October 21, 2017
After sanding & smoothing
34 October 22, 2017
These tires will be impossible to get right without rescribing. Which I won't be doing.
35 October 22, 2017
Left original, right treated.
36 October 22, 2017
Almost forgot a red part.... This one actually is pretty clean. Just some very light sanding.
37 October 22, 2017
And some ugly marks here and there.
38 October 22, 2017
Cleaned up.
39 October 22, 2017
Degreased and drying. Time for priming!
40 October 23, 2017
First batch primed Alclad High Gloss Black. Started with the interior and noted I accidentally had loaded Alclad matt black microfiller. Luckilly I didn’t start with the cab.
41 October 25, 2017
Test piece. To the right Alclad 107 Chrome over Alclad’s black microfiller primer. To the left same Chrome over Alclads High Gloss black primer. Spot the difference 😉
42 October 28, 2017
Quite happy with the result
43 October 28, 2017
Lower parts of the stacks painted silver
44 October 28, 2017
Some details painted.
45 October 28, 2017
The grill
46 October 28, 2017
Chassis matt black
47 October 28, 2017
Engine & parts painted. i wanted a casted look for the ochre part. Went okayish.
48 October 28, 2017
Tires painted mig 'rubber and tires'
49 October 28, 2017
The interior of the cab. First ever attempt to do high/low lights
50 October 29, 2017
Choices. Which logo should I use?
51 October 29, 2017
Picked the top one. Cut out the shapes in the masking tape. Screwed up the lower left one. Is going to be tricky to get them right on the model.
52 53 54 October 29, 2017
Purplish metallic decepticon colour
55 October 29, 2017
The result! Quite satisfied with this. The masks for the mud flaps were too fragile.
56 November 1, 2017
Assembly is easy.
57 58 59 60 November 1, 2017
Cab getting there.
61 November 1, 2017
Stacks n stuff
62 November 1, 2017
Stacks mounted
63 November 1, 2017
Horns and lights
64 November 1, 2017
Blunt force trauma
65 November 1, 2017
Danger in the rear view mirror
66 67 68 69 70 71 评论 27 November 2024, 20:55 -
Album info This will be my Decepticon Motormaster. Ever since I saw this kit, I wanted to do this 🙂
71 图片
1:32
已完成
所有相册 查看所有相册 »