Альбомы (135)

Baseparts assembled

And now with 40% buff and 40% olive drab and 20% clear...

Yardarms for aerials added, 0.2mm copper wire, base completely soldered

and mounted

Tower being build up

Main hull part

Added handles and pivot axles. Front fender for lamps made thinner (left vs right)

Just some gentle scraping with the tip of a knife

Removed the front fenders

Kit part

And barrels dryfitted

White is on

Breakwater partly broken

For size...

booklet

Other details too

Almost ready, and not only for the nuthouse or optician...

total overview so far...

Added some handles

For the difference

Hollowed out the muzzle break

Finished

Some weird mold fail...

Still some last details to do and some checks.

Mg's soldered... not perfectly aligned at the muzzles, but it's 3 layers and size you can compare with the butchers knif...

Side consoles and floor..

First half side done

Sight... very comprehensive...

a mean machine...

but when checking with the glass parts it becomes another story... the angle is completely off. Need to think hoh to cop...

result...

Started PE-cabin from eduard... Middle vertical wall is a few mm short

not that big after all

An idea of the set-up I'd like... If it doesn't work out with the smoke, it will be less dramatic...

and adapted

first fender complete

a small one in the end

dryfit

dryfit of the main parts...

wheels and tracks mounted

last dials added

Almost complete, and ready for primer, only parts missing are for ease of painting

All complete

the jolly threesome... The T-14 and T-15 are giants compared to the Terminator on a basic T-72 chassis

dryfit of the cupolla.... can be totally disassembled...

main hull

general overview

nose + guns...

Main hull parts

without flash

added the guiding lines for attempt to add canning

dry-fit

real version ;-)

Finished

Hull parts and tracks

boxart

dryfit for size, pretty big...

a lot of ejection marks on the inside of the vehicle to be filled, also on the towing hooks etc...

tracks in basepaint...

Main truck parts

Main truck parts

Main radar parts and operator cabin

Started soldering the armored cab

a bit of corrections to the tub...

some necessary filling was needed...

Hull and wing parts

To obtain the double curvature from the disk I'll try to make it in styrene or PE

cockpit front

redid the hood, removed the paper and added aber tie downs, to make it more convincing

PE and details added, more to do

almost there

Hull assembled, still need to check whether the pontons have a flush fit

hull parts, even the old airfix panellines are small compared to this...

Wing cut-outs made and dryfit of the flaps, still need to wait till the wings are joined with the hull

removed all necessary details, time to start with filler and adding stuff

and it's mega-size, still regretting the airco dh-1 1:144 as stripdown-model

Complete overview, very small box for such a large aircraft

fully stripped above...

Ready for primer

not that much parts

it's small

first cockpit getting ready, 3 to go

Cupola finished and ready to try to clean-up

made some shoes... which size fits best?

Ready for reinforcement beams

tested with black paint to check the seams, looks ok after a few iterations

Rear fins done

some try at the black and white technique

hull and wheels in one part

drilled out lifting eyes, replaced handles

hull parts

boxart

Upper hull mated and started detailing

flush fit with the green border... 1mm gap on the indicated side

Dials

Frontal wings added

started soldering the sideconsoles

Finally finished!!!

Main hull, one solid part, track guides are separate

interior almost complete

Upper torso... drilled and scraped for sharper result

First pe-works, not a novice, but still another level

busy cleaning up and dryfitting

painted the tracks.... finally

Sprue's

some PE on the other side too... still not even halfway...

added the plates at the sides of the cockpit

bottom hull completed

it's small

general view

cockpit with basic detail

all welcome