PLA Type 22

1
February 15, 2017
Main parts
2
February 15, 2017
Main hull parts
3
February 15, 2017
Main hull and bridge
4
February 15, 2017
Railings and miscelaneous
5
February 15, 2017
Missiles and clear parts
6
February 15, 2017
PE
7
February 15, 2017
decals
8
February 17, 2017
should be filled
9
February 17, 2017
so some sprue to fill most, then putty, to avoid melting the plastic by the dissolvants
10
February 17, 2017
after sanding
11
February 17, 2017
basic mast
12
February 17, 2017
removed steps, and drilled holes
13
February 17, 2017
brass wire 0.3mm
14
February 17, 2017
steps in their places, by pressing them to the surface they set themselves to the width of the hole
15
February 17, 2017
the I pull them randomly forward
16
February 17, 2017
Here i place some spacers (2 drills of 0.5mm in this case), to get an equal distance for each step
17
February 17, 2017
I glue them mostly on the inside with thin CA, but here it is hard to reach, so I glued them on the outside too. Some CA residue is visible
18
February 17, 2017
inside view, pretty cosy
19
February 17, 2017
3mm glassfibre pen to the rescue, along with some slight scraping with a scalpel first
20
February 17, 2017
cleaned up
21
February 28, 2017
thinning the walls
22
February 28, 2017
radar-unit seemed thick
23
February 28, 2017
thinned the walls by scraping them round
24
February 28, 2017
added the guiding lines for attempt to add canning
25
February 28, 2017
added the guiding lines for attempt to add canning
26
February 28, 2017
Example of canning, don't know the exact word
27
February 28, 2017
Example of canning, don't know the exact word
28
March 1, 2017
first blood, euuhm dust...

Comentários

1 15 February 2017, 14:27

Łukasz Gliński
Interesting, will follow

15 February 2017, 20:25

Bart Goesaert
thx. Just started with the hull, I think I will need to spray the inner parts of the catamaran-arm first before glueing the lower hull together. So far, it assembles as a breeze... You don't have the option to open up the launching louvres for the missiles as if they should be launched, maybe...

16 February 2017, 10:10

Bart Goesaert
a little how to for the placing of the steps. In the end with a small plier I twist the steps a bit till they are all horizontal.

17 February 2017, 12:48

Bart Goesaert
on to e decent attempt to add some "canning"...

28 February 2017, 13:32

Łukasz Gliński
Trying to find definition of canning over the internets, but can't find anything connected to modelling - can you write sth more about that idea?

28 February 2017, 19:07

Bart Goesaert
Placed two picture of what I Mean, but don't know the exact word for that effect. These picture are from the link below:
modelshipwrights.com..id=134748&page=1

28 February 2017, 19:26

Łukasz Gliński
Interesting, but aren't those Chinese boats too new for such effect?

28 February 2017, 20:41

Martin Oostrom
After just one trip in too rough seas this effect can be seen. Most self respecting captains try to avoid it though. Not good for their career 😉

28 February 2017, 20:52

Bart Goesaert
don't want it to be overdone, but it sure looks nice on the boxart... that's why I want to try it...

1 March 2017, 07:07

Martin Oostrom
Almost looks like the skin is vacuum sucked over the ribs and springers.

1 March 2017, 11:12

Martin Oostrom
According to this site: chinadailymail.com/2..speed-missile-boats/
The hull is made of aluminum. Perhaps that explains the ribbing. Steel would not have been affectee like this on the superstructure.

1 March 2017, 11:19

Album info

PLA type 22 anti ship catamaran. Interesting subject and camouflage.

PLA Chinese Navy Type 22 Missile Boat

28 imagens

1:144

Idéias

Todos os álbuns

Ver todos os álbuns »