TIE Whisper Interceptor
![Album image #1 Album image #1](/albums/img/1/7/3/1032173-27411-45-720.jpg)
Added some sections of 0.4mm rod to give some variation to the wing panels
![Album image #2 Album image #2](/albums/img/1/7/4/1032174-27411-97-720.jpg)
Removed the rear seat and added some bits from the greeblie pile.
![Album image #3 Album image #3](/albums/img/1/7/5/1032175-27411-58-720.jpg)
Also used some scrap styrene to fill holes and add a bit more detail.
![Album image #4 Album image #4](/albums/img/1/7/6/1032176-27411-79-720.jpg)
Added a casting of the front panel, based on the one I modified for the standard TIE Whisper build
![Album image #5 Album image #5](/albums/img/1/7/7/1032177-27411-72-720.jpg)
Cockpit in place - with a Kylo Ren figure made by modifying a FO pilot body and adding a left-over Anakin Skywalker head (originally from a Fine Molds Jedi Starfighter kit, I think)
![Album image #6 Album image #6](/albums/img/1/7/8/1032178-27411-71-720.jpg)
Basic body put together - wing centre pieces just clipped in place for now.
![Album image #7 Album image #7](/albums/img/1/8/0/1032180-27411-67-720.jpg)
New windshield attached - again from a casting made during the standard TIE Whisper build
![Album image #8 Album image #8](/albums/img/1/7/9/1032179-27411-74-720.jpg)
Hull extension put in place - front view
![Album image #9 Album image #9](/albums/img/1/8/1/1032181-27411-79-720.jpg)
Rear view showing hull extensions in place
![Album image #10 Album image #10](/albums/img/0/4/4/1034044-27411-75-720.jpg)
I had painted the wing panels but wasn't happy with the gaps around the inserted ribs - so I had a go at puttying them a bit. Also I wasn't happy with the colour - too warm. I'll have to mix up a new colour later.
![Album image #11 Album image #11](/albums/img/0/4/5/1034045-27411-15-720.jpg)
Dry fits of the wing outer and inner sections showed a gap for one section on each side. A shim was made from scrap styrene, glued in place and trimmed to match the opposite side.
![Album image #12 Album image #12](/albums/img/1/9/2/1040192-27411-77-720.jpg)
Wing panels glued together - some repositioning required as they are a long way from parallel
![Album image #13 Album image #13](/albums/img/1/9/3/1040193-27411-53-720.jpg)
Wing panels repositioned and gaps filled
![Album image #14 Album image #14](/albums/img/7/7/7/1040777-27411-36-720.jpg)
Wing-tip guns glued in place and a coat of black primer on the wings
![Album image #15 Album image #15](/albums/img/5/1/9/1041519-27411-53-720.jpg)
Gaps under the extensions filled with Aves and a coat of interior grey on the transparencies - also used it as a primer to check the filled areas.
![Album image #16 Album image #16](/albums/img/3/2/7/1067327-27411-56-720.jpg)
Main painting completed on all parts and coated with Future ready for weathering
![Album image #17 Album image #17](/albums/img/2/2/9/1070229-27411-67-720.jpg)
![Album image #18 Album image #18](/albums/img/2/3/0/1070230-27411-95-720.jpg)
![Album image #19 Album image #19](/albums/img/2/3/1/1070231-27411-28-720.jpg)
![Album image #20 Album image #20](/albums/img/2/3/2/1070232-27411-83-720.jpg)
![Album image #21 Album image #21](/albums/img/2/3/3/1070233-27411-55-720.jpg)
![Album image #22 Album image #22](/albums/img/2/3/4/1070234-27411-48-720.jpg)
![Album image #23 Album image #23](/albums/img/2/3/5/1070235-27411-91-720.jpg)
![Album image #24 Album image #24](/albums/img/2/3/6/1070236-27411-17-720.jpg)
Comments
30 July 2024, 08:39 -
Album info
This is the ship Kylo Ren flew in Rise of Skywalker. It's based on the Bandai First Order Special Forces TIE Fighter, with the Modelwerks conversion kit.