Honda Integra(DC5) - WIP Part01
1November 7, 2018cutout
2November 7, 2018cutout
3November 7, 2018cutout
4November 7, 2018trimming and polishing
5November 7, 2018panel lining
6November 7, 2018panel lining
7November 7, 2018white surfacing
8November 7, 2018drawing air intake hole
9November 7, 2018cutout air intake hole
10November 7, 2018cutout air intake hole
11November 7, 2018detail-up air intake hole edge and painting gloss white
12November 7, 2018washed
13November 7, 2018cutout fin
14November 7, 2018compounding for transparent
15November 7, 2018triple overcoat clear
16November 7, 2018compounding and water washing
17November 7, 2018compounding and water washing
18November 7, 2018compounding and water washing
19November 7, 2018compounding and water washing
20November 7, 2018ready for painting semi gloss black
21November 7, 2018masking
22November 7, 2018painting semi gloss black
23November 7, 2018take off masking tape
24November 7, 2018painting flat, semi gloss black to another parts
25November 7, 2018take off masking tape and water washing
26November 7, 2018masking again for silver, red painting
27November 7, 2018trimming rough painted area
28November 7, 2018light weathering with tamiya weathering master
29November 7, 2018roughly painting and weathering
30November 7, 2018paint brushing
31November 7, 2018painting rear lamp and side winker
32November 7, 2018making side winker on fender
33November 7, 2018punching '3M' mirror tape
34November 7, 2018and stick to rear lamp
35November 7, 2018I don't know what is this... but I saw it on the box art
36November 7, 2018black lining to panel line
37November 7, 2018snipping nylon mesh
38November 7, 2018applying mesh
39November 7, 2018applying mesh
40November 7, 2018assembling wheels
41November 7, 2018applying decal and gloss coating
42November 7, 2018applying wheels
43November 7, 2018applying option metal transfer emblem
44November 7, 2018detail up harness with etching(option parts)
45November 7, 2018detail up harness with etching(option parts)
46November 7, 2018detail up harness with etching(option parts)
47November 7, 2018assembled
48November 7, 2018cockpit on the board
49November 7, 2018detail up with etching(option parts)
50November 7, 2018painting emblem etching(option parts)
51November 7, 2018attached
52November 7, 2018attached
53November 7, 2018applying metal transfer(option parts)
54November 7, 2018attached side winker
55November 7, 2018attaching rear bumper
56November 7, 2018and attaching front bumper and front lamp cover
57November 7, 2018and attaching rear lamp cover
58November 7, 2018detail side mirror with black of bandai pokemon sticker 🙂
59November 7, 2018sttaching side mirror
60November 7, 2018attaching rear wing
61November 7, 2018finish, but this kit had critical problem
62November 7, 2018that was strange proportion or wheel house
63November 7, 2018because too large wheel house or too small rims
64November 7, 2018because too large wheel house or too small rims
65November 7, 2018because too large wheel house or too small rims
66November 7, 2018anyway I'm done.
Comments
7 November 2018, 09:53
Alexander GrivonevGreat, thanks! What paint and clearcoat do you use for the body?
7 November 2018, 11:44
