Mustang GT4 KohR Motorsports 2018 - JobLog
1September 17, 2022Painted black surfacer.
2September 17, 2022Masked under plate.
3September 17, 2022From left...
White surfacer | Silver | Titanium silver | Copper | Flat Aluminium | Gunmetal
4September 17, 2022Gloss black | Shine red
5September 17, 2022After masking the bonnet, I painted gloss black.
6September 17, 2022Mask again under palte.
7September 17, 2022Gold | Titanium gold
8September 17, 2022This is Hasegawa's big size mirror film. (same with Hasegawa Mirror Finish)
9September 17, 2022Applied to the left door.
10September 17, 2022Applied to the right door.
11September 17, 2022Apply to front fender.
12September 17, 2022Done.
13September 17, 2022Applied to the rear fender too.
14September 17, 2022Other side.
It took about 3 hours.
15September 17, 2022Applied the decal on it.
16September 17, 2022All decal works done. (Very nice decal quality)
17September 17, 2022
18September 17, 2022Clear coated.
It seem no problem. But.....
19September 17, 2022Blurry iridescent stain appeared under the transparent layer.
20September 17, 2022Blurry iridescent stain appeared under the transparent layer.
21September 17, 2022Blurry iridescent stain appeared under the transparent layer.
My guess is that I rubbed too hard with a cotton swab to remove the decal adhesive, and there must have been a chemical reaction between the scratch on that area and the lacquer clear.
And I applied the clear very soked, but it would have been better if I first coated it lightly and moistly in advance, dried it, and then drenched it and painted it.
22September 17, 2022It was coated without any problem on the non-chrome reflective areas.
23September 17, 2022Stains are less visible in natural light.
24September 17, 2022Stains are less visible in natural light.
25September 17, 2022Stains are less visible in natural light.
26September 17, 2022Stains are less visible in natural light.
Fortunately, it is invisible from a normal point of view, and only appears when you hold it high with your hand and deliberately reflect it in the light.
27September 17, 2022Of course, there is no problem in natural light for non-mirror surfaces too.
28September 17, 2022Sanded.
29September 17, 2022The marked place is the step difference caused by cutting and pasting the mirror sheet.
30September 17, 2022The decal was shaved off by excessive sanding.
31September 17, 2022The decal was shaved off by excessive sanding.
Greed brings misfortune.
32September 17, 2022painted with brush paint.
33September 17, 2022Compounded after Final clear coated.
34September 17, 2022Brush painting again.
35September 17, 2022In fact, the biggest difficulty of this livery is not the chrome expression on the side, but the star expression on the bonnet.
It should be a glossy black star over the matte bonnet.
36September 17, 2022So I had to cut out every star one by one.
37September 17, 2022It was not easy to match the lines, spacing, and angles, but the result is satisfactory.
38September 17, 2022Ready to assemble.
39September 17, 2022Finish.
The assembly process was omitted because it was no different from the previously made 'VOLT' vehicle.
VOLT vehicle's job log is here.
motorart.tistory.com/405
motorart.tistory.com/419
motorart.tistory.com/424
40September 17, 2022Finish.
The assembly process was omitted because it was no different from the previously made 'VOLT' vehicle.
VOLT vehicle's job log is here.
motorart.tistory.com/405
motorart.tistory.com/419
motorart.tistory.com/424
Kommentarer
26 December 2024, 03:36 -
Album info
FHD images are here.
motorart.tistory.com/535
