Bordurian Westland Lysander

1
August 28, 2022
Printed Bordurian Roundels )with a red outer ring to show up against the black overall colour)
2
August 28, 2022
Injector marks on inside filled or sanded (both are needed!) and some areas thinned
3
August 28, 2022
Interior put together and glued to one side
4
August 28, 2022
Fuselage glued together
5
August 28, 2022
Vac-form canopy sections masked before separating as it seemed easier
6
August 28, 2022
Canopy sections sprayed interior green on the outside to make it easier to see where to cut
7
August 28, 2022
Landing gear pieces - I have thinned the inside of the spats (one half of each side is very thick) and added a sanded-down strut (which is designed for use on the version with opened-up spats)
8
August 28, 2022
Landing gear pieces painted
9
August 28, 2022
Landing gear glued together, filled and sanded
10
August 28, 2022
The propeller comes as a resin hub and injection molded blades and spinner. I drilled 0.4mm holes in all and pinned the blades with steel wire. Here the blades are being glued in place using a Kora jig
11
August 28, 2022
Finished propeller
12
August 28, 2022
Resin engine cleaned, repaired and painted and cowling glued together. Interior and front of cowling have also been painted
13
August 30, 2022
Front and back sections of canopy attached. Found the moulded-on wing mounts were set too low, so I glued on replacements set higher and cut off the originals
14
August 30, 2022
Top section of canopy attached. Some of the original masking didn't survive and will be replaced.
15
August 31, 2022
Landing gear lights include a resin light and a vac-formed cover. The cover had to be roughly shaped, glued in place and then heavily sanded to shape and polished (luckily its quite thick). Here the left shows the components and the right is complete
16
August 31, 2022
Main landing gear complete and attached.
17
September 1, 2022
Canopy repairs completed and re-masked. Engine and cowling attached and tail surfaces attached. Starting to look like a Lysander
18
September 1, 2022
And finally wings attached - some clean-up needed on the strut joins to the wings and undercarriage but after that, and a bit more masking, it will be on to paint
19
September 2, 2022
A coat of gloss black has been sprayed on, touch-ups done where needed, Clearfix windows added at the back and final bits added. Ready for decals tomorro
20
September 3, 2022
Decals applied - probably could have made the red circles a bit broader but I'm reasonably happy with them
21
October 30, 2022
22
October 30, 2022
23
October 30, 2022
24
October 30, 2022
25
October 30, 2022
26
October 30, 2022
27
October 30, 2022
28
October 30, 2022

Opmerkingen

18 28 August 2022, 01:07

Bas Tonn
Great work on all your Tintin builds, very impressive !!

28 August 2022, 06:45

Uwe Kaeding
Thanks Bas - they're fun things to build as you don't have to be super accurate (they can sometimes change from panel to panel in the books) and some of them you see so little of that you can be as creative as you want!

30 August 2022, 06:44

Matthew A
Brilliant

30 August 2022, 08:55

Łukasz Gliński
Watching, not a big Tintin fan, but I have the very same kit in my stash and wonder how bad it could be 😄
Very useful vacu canopy hints, thx

30 August 2022, 08:59

Uwe Kaeding
Thanks Matthew. Lukasz - its a short-run kit, but certainly not the best version of those. I had to sand down the inside of trailing edges of the wings before gluing the halves together to make them look decent. I also had to go around every injection moulded piece looking for extra areas of plastic that needed to be trimmed off (the two windows at the rear of the fuselage were bad - one was completely closed over and had to be drilled out and then filed to shape.) and lots of flash as well, especially on the cockpit interior parts. However the detail is quite good and I'm hoping it will turn out OK.

30 August 2022, 13:36

Guy Rump
Looking good 👍

2 September 2022, 10:43

Torsten
Well done 👍

11 September 2022, 18:14

Guy Rump
Very nice build 👍

12 September 2022, 08:33

Spanjaard
Looks great.

12 September 2022, 08:39

Uwe Kaeding
Thanks for comments and likes - this one is done now, just waiting for some final photos

13 September 2022, 05:01

Uwe Kaeding
Final photos now taken

30 October 2022, 00:16

Album info

While Tintin and crew are at the Syldavian moon launch facility it is overflown by an unknown plane (presumably Bordurian) that looks a lot like a Westaland Lysander. I've chosen to build the Pavla Lysander Mk.II kit, largely out of the box, except for a replacement Lewis gun from the spares box (as the kit item is pretty crude) and a Yahu instrument panel. The plane is only shown in silhouette in the book so I'll paint it black as a night infiltration/spy plane with home-made Bordurian markings

Destination Moon

50 afbeeldingen

1:72

Lopend project

1:72 A4/V2 Prototypes (Special Armour SA72014)

1:72 Douglas DC-6B Super Cloudmaster (Heller 80315)

1:72 Pratt & Whitney R-2800 set (Engines & Things 72147)

1:72 Hiller UH-4 "Commuter" (Unicraft Models )

1:72 Hawker Hurricane Mk.IV. (AZmodel AZ7389)

1:72 Westland Lysander Mk.II (Pavla Models 72048)

Alle albums

Bekijk alle albums »