BMW Z4 Hatsune Miku 2014 - WIP

Washed. 

Engraved panel line to deepely and sanded. 

The front and rear mesh grilles are blocked and the mold is shallow, so it needs to be modified. However, the rear has a complicated shape and the pins for joining the lower plate are located on the inner side, so it is troublesome, so I decided to modify only the front.
 

I pasted it onto the etching mesh and cut it out leaving a little margin. 

Now that the molded mesh has been removed, there are pins on the inside of the front to join the lower plate, but fortunately, when I cut them off, about 2/3 of them remained, so there is no problem joining the lower plate. 

Next, cut the plastic sheet to an appropriate size... 

I created steps so that I could stick the mesh at the same depth. 

It will be attached like this later after painting. 

The vents on the bonnet were two piece, so I glued them together and then applied putty. 

I noticed this detail on the box art, but it was omitted from the kit. 

To make it roughly similar, I cut out offof the grill's vertical bars and drilled a hole in the back plate. 

Then I'm thinking of coloring and fitting similarly shaped metal parts. 

Sanded it. 

This is a car that uses a lot of carbon, but it would be difficult to express everything, so I decided to express only a few visible areas.
So I painted the areas where I wanted to express carbon in glossy black, and the rest in matte black.
The glossy black is the new GGX paint from GSI that I used this time, but it doesn't look as good as I thought.
I think the Ueno Black that I used before is better. 

I forgot to paint the inside of the body shell.
And I painted the rear grill and the front windshield area around too. 

Masked. 

Assembled roll cage for painting. I pressed it down because the parts didn't fit together well. 

White Surfacer. 

And, I painted it in glossy white.
The side mirrors are in two colors, top and bottom.
They are supposed to be attached with decals, but I was worried that it would be annoying to attach them, so I mixed green with reference to the color of the decal and painted it. (blue arrow: bright green)
I will have to paint the pink one more time later. 

It was only later that I realized that this was a tow belt. 

After I cut it out, I trenched it with guide tape. 

It's not very clean since I can't sand it down, but I guess it doesn't matter since I'll be doing decals and clear coating anyway. 

I folded the red line tape and put it in. I used 1.5mm width now, but I think it will fit perfectly if I use 2mm width later. 

The hole was blocked, so I unclogged it. 

After I've trimmed all the parts, I can keep a GT wing, two sets of sleek side mirrors, and a rear diffuser as spares. 😛 

I also painted the pink parts by referring to the decal. 

The remaining parts were also painted with airbrush. 

Carbon patterns were painted on complex-shaped parts using stockings. 

Now I have to apply the decals, which are the alpha and omega of this kit. It is very difficult because it is fragmented and has to be applied in 3-4 layers, so I have to be determined. So I played around for about 3 days watching Netflix. 

I bought this kit used, and although the decals didn't yellow, I was worried because the paper was stiff, as if it had absorbed moisture and then dried. So I cut out the parts that I wasn't going to use and tried attaching them, and fortunately, it seemed okay.

scalemates.com/profi..=88894&i=109#109
Compared to this, this is in really good condition. 

It took a long time for the decal to separate from the paper. It felt like putting a decal that had been wet once and then dried back into water. 

The side would seem to be more complicated than the bonnet, so I applying carbon decals for relatively. 

Done.
Unexpectedly attaching the wing was more difficult than the front splitter. 

Since the shape is simple, I did vector work to utilize the product of new generation I had. 😉 

This is cutter plotter. 

The size was cut too small due to a miscalculation of the dpi. 

I cut it again and pasted it on, but even though it was white decal paper, the base color showed through. 

So I roughly cut out just the text part from the enclosed decal. 

Done.