[Tamiya] Ford Mustang GT4 (Job Log)Vista: Presentazione Mosaico Elenco 1March 6, 2022I stabbed my finger and it hurts. It is very sharp, so be careful. 2March 6, 2022Don't cut. 3March 6, 2022I will remove this mold. 4March 6, 2022Trimming and washing. 5March 6, 2022I painted inside to black for anti subsurface scattering. 6March 6, 2022L: Fluorescent yellow. R: Overcoated in a light yellow. 7March 6, 2022Done. 8March 6, 2022L: Need cut off. R: Carbon pattern not printed properly. 9March 6, 2022I drew a vector logo to try out a laser engraver. 10March 6, 2022I put masking tape on the PET and cut it. 11March 6, 20221st: Stick to outside. 2nd: Stick to inside. 3rd: Remove outside. 12March 6, 2022And, I paint with a black and carbon pattern. 13March 6, 2022Then I remove it. But, the edge was not clean. 14March 6, 2022Hahaha I'm going to erase everything and use the decals. 15March 13, 2022White surfacer (Gloss). 16March 13, 2022Gloss clear coated (once) 17March 13, 2022L: Momodeling fluorescence yellow (I use this) R: IPP fluorescence yellow Maybe I think 'L' is not pigment type. 18March 13, 2022Print miss. So I didn't use the little decals. 19March 13, 2022Decaling done. 20March 13, 2022Various base colors were painted on the small parts. 21March 13, 2022'Gloss Black' and 'Gloss Clear' coat. 22March 13, 2022Gloss clear coated. (once) 23March 13, 2022Compounding done. But paint has been erased. 24March 13, 2022Tamiya Pannel Line Accent. 25March 13, 2022Problems occurred when removing the tape after masking and painting only the erased areas. 26March 13, 2022Heavy trouble.... 27March 13, 2022When I carefully removed the decal film, the film was intact and only the ink was attached to the masking tape. 28March 13, 2022Inevitably, I have to make letters with stencils. 29March 13, 2022This time, I masked the decal as carefully as possible so that it doesn't fall off again. 30March 13, 2022I think the result is quite satisfactory. 31March 13, 2022Gloss coated and polished(rough). 32March 16, 2022Masking... 33March 16, 2022Done. 34March 16, 2022Black surfacer. 35March 16, 2022Carbon pattern using stockings. 36March 16, 2022Partial painting with a brush. 37March 16, 2022I was worried that the decal would come off again if I masked it, so I painted the window frame with a brush. 38March 16, 2022Ready to assemble. 39March 16, 2022The interior decals are from Tamiya. 40March 16, 2022I used a silver foil sticker from GunPla. 41March 16, 2022Assembling the lower part 42March 16, 2022Tires and windshield. (Indycals) 43March 16, 2022Pre-assemble. 44March 16, 2022Interior done. 45March 16, 2022Interior done. 46March 16, 2022Interior done. 47March 16, 2022I missed. Painted with 'Vallejo Mecha Black Primer'. 48March 16, 2022Assemble, Re 49March 16, 2022Assemble, Rear 50March 16, 2022Assemble, Front. 51March 16, 2022Assemble, Front. 52March 16, 2022I used Hasegawa 'White Finish' for the inside of the headlamps, which should be painted white. 53March 16, 2022I cut the metal sticker included with the Tamiya case and apply mirror. 54March 16, 2022Attach everything that needs to be attached inside the shell... 55March 16, 2022And after joining the upper and lower plates, I attached the under cowl. 56March 16, 2022Finally, attach the rest of the exterior parts and done. 57March 16, 2022Finish~ Commenti23 December 2024, 06:35 - Album infomotorart.tistory.com/405Mustang GT4 Volt Racing106 immagini1:24CompletatoTutti gli albumVisualizza tutti gli album »