Harrier gr7 1/144Vista: Presentazione Mosaico Elenco 1August 16, 2021First try at the cockpit 2August 16, 2021For size... 3August 16, 2021 4August 16, 2021Thinning the borders or replace with pe... 5August 16, 2021Scraped to make thinner 6August 16, 2021Before and after 7August 16, 2021 8August 16, 2021 9August 16, 2021Filled the seam between the wing parts 10August 21, 2021Cockpit installed 11August 24, 2021Opened up the airbrake 12August 24, 2021Took the contours by putting some paper over it an rub it with a pencil 13August 24, 2021What I want 14August 24, 2021To adjust a bit 15August 24, 2021Finished 16August 24, 2021Dryfit 17August 31, 2021Was trying to add the ribs, but sanded through the hull... so added a new backing with paper. 18August 31, 2021Had to make a hole to be able to push the backing down. 19August 31, 2021Adding some antennas 20August 31, 2021Adding some antennas 21September 3, 2021took a start on the landing gear... 22September 7, 20211 down, 1 to go... 23September 15, 2021And his brother... difference in fin position is 0.5mm... damn 24September 15, 2021Retrokit inlets... some difference 25September 15, 2021Glued some extra meat 26September 15, 2021And refueling probe 27September 15, 2021After some cutting 28September 15, 2021And extra meat sanded 😉 , refueling probe minus the tube installed 29September 24, 2021 30September 23, 2021Some dimensions of the LAU-5003 rocket launcher 31September 23, 2021Makeshift lathe 32September 23, 2021Makeshift lathe, paper is to prevent dents from the clamping mechanism 33September 23, 2021Lining could be better 34October 5, 2021Kit canopy 35October 5, 2021Wooden mold 36October 5, 2021Just heat a piece of plastic packing (now one of revells packaging of kit and paint) and it over the "mold" 37October 5, 2021Result 38October 20, 2021Canopy in two parts, but I tend to keep bending it despite the blutack in the last steps while adapting the rear of the main part... 39November 4, 2021Finally... 40December 20, 2021First color 41December 20, 2021Taping 42December 20, 2021More tape 43December 20, 2021Second color 44December 20, 2021Untaped, on to the next color 45December 20, 2021 46December 22, 2021Next color 47December 22, 2021Next color 48December 22, 2021Leading edges handpainted 49December 22, 2021Leading edges handpainted 50December 26, 2021Another maskingsession 51December 26, 2021Another masking session 52December 26, 2021And unwrapped 53December 26, 2021And unwrapped 54December 27, 2021Missiles taped in 55December 27, 2021And brushpainted 56December 27, 2021For size 57December 31, 2021On it's own feet for the first time... 58January 20, 2022Lost the decals for these... so tried with the AB 59January 20, 2022Lost and found... pull handle 60January 20, 2022Bang seat mounted 61January 20, 2022And installed 62January 20, 2022Decals... 63January 20, 2022And some more... not that much 64January 20, 2022Overview 65January 26, 2022Tried it with CA, but got foggy after filling the gaps... 66January 26, 2022 67January 26, 2022 68January 26, 2022Now with PVA glue 69January 26, 2022Some slight sanding to do, but... happy 70January 26, 2022Rearview mirrors installed 71January 27, 2022Done... 72January 27, 2022Done.. 73February 8, 2022 74February 8, 2022 75February 8, 2022 76February 8, 2022 77February 8, 2022 78February 8, 2022 79February 8, 2022Finished Commenti23 December 2024, 10:22 - Project infoBAE Harrier GR.779 immagini1:144CompletatoTutti gli albumVisualizza tutti gli album »