Ukrainian Su-27S 1/144

1
June 30, 2022
Original lower fins
2
June 30, 2022
Thinned down fins
3
June 30, 2022
Main upper hull
4
June 30, 2022
Removed a few things
5
June 30, 2022
Cutting out a recess for the PE guncover
6
June 30, 2022
Dryfit
7
July 5, 2022
Original 😉
8
July 5, 2022
Sanded the wheelcover into shape, added the louvres. Still need to add the connections of the cover to the main tube. The grooves have been a bit more cleaned since this picture
9
July 5, 2022
Added some wiring with stretched sprue... Still 2 more landing lights to add
10
July 7, 2022
Making extra lights
11
July 7, 2022
Mounted
12
July 7, 2022
Finished upto the two bars that are attached to the protective cap for painting reasons
13
July 7, 2022
Some wires here too
14
July 12, 2022
Retrokit cockpit vs kit cockpit
15
July 10, 2022
Front wheel cover ready as per kit... still need to make the recess for the landing gear system
16
July 12, 2022
Cleaning the surface with a glass fibre pen
17
July 12, 2022
Adding some flux and presolder the connecting surfaces
18
July 12, 2022
Clean again... then place on each other and apply heat...
19
July 13, 2022
Lay the pieces on eachother and apply heat
20
July 12, 2022
After bending some dimensional errors... PE piece is a lot smaller then the plastic opening... Bit in doubt whether to sand away the bulge or just continue...
21
July 13, 2022
Then bend... and all finished
22
July 13, 2022
factory fresh 😉
23
July 13, 2022
cut away for resin
24
July 13, 2022
testfit
25
July 27, 2022
remove more material
26
July 27, 2022
bummer...
27
July 28, 2022
Cockpit
28
July 28, 2022
Bangseat
29
July 28, 2022
Joystick
30
August 1, 2022
Engine entrance, just in case it would be visible. I've thinned the outer walls also and filled the holes.
31
August 1, 2022
Not that visible after all
32
August 1, 2022
Hull parts glued and sanded. Nose was a bit wide, but in the end
33
August 1, 2022
And the gun cover...
34
August 1, 2022
35
August 1, 2022
Dryfit
36
August 2, 2022
Original
37
August 16, 2022
Added some sensors and the bulges to lock the landing gear
38
August 15, 2022
First missile...
39
August 15, 2022
Some very small parts
40
August 15, 2022
For size
41
August 15, 2022
With 2 brothers... or sisters..
42
August 19, 2022
Basic PE-fret
43
August 19, 2022
Parts cut loose
44
August 19, 2022
To deburr, I use a plier without teeth (flat surface)
45
August 19, 2022
Sand the burrs off with a fine file
46
August 22, 2022
Then a bit of CA to start with, and some carefully positioning
47
August 19, 2022
5 more to go...
48
August 25, 2022
Almost ready, and not only for the nuthouse or optician...

Hozzászólások

22 30 June 2022, 20:41

Bart Goesaert
Started cutting some things up a bit...

30 June 2022, 20:46

Spanjaard
really curious about this one 🙂

30 June 2022, 21:24

Bart Goesaert
thx Spanjaard, me too honestly...

1 July 2022, 05:43

Robert Podkoński
Watching with interest!

1 July 2022, 05:45

Robin (WhiteGlint)
Looks like this tiny kit will receive quite a lot of modifications. 👀

1 July 2022, 10:57

Bart Goesaert
Thx for interest. I hope to get some result in the end... started work on the front landing gear.

5 July 2022, 20:39

Bart Goesaert
Construction of the landing gear finished

7 July 2022, 20:45

Sergej I
Scratching gear details in 144th scale? I'm in, this is beyond what I could even imagine 👍

10 July 2022, 12:09

Bart Goesaert
Thx for interest.

11 July 2022, 08:16

Bart Goesaert
Started soldering the other wheelwellcovers.. pe parts differ a bit from kit parts dimensionally. Don't if they are based on the real doors or what is going on now... Checking everything to see if it is a big deal when positioned open (it's on the underside)...

12 July 2022, 11:36

Bart Goesaert
Wheelbaycovers soldered... ready to clean

13 July 2022, 21:13

Bart Goesaert
Dryfit... PE is too large it seems.. will build the rest first and see what can be done after a general dryfit...

28 July 2022, 06:13

Bart Goesaert
Cockpit ready to be built in

28 July 2022, 21:51

Bart Goesaert
Hull glued, ready to detail

1 August 2022, 16:19

Bart Goesaert
Started the missiles

15 August 2022, 20:49

Matthew A
Wow

15 August 2022, 21:08

Cosiek
A real pleasure to watch.

15 August 2022, 21:31

Erik Off
OMG! Awesome! 👍

16 August 2022, 07:07

Łukasz Gliński
Impressive, keep it up 👍

16 August 2022, 07:22

Bart Goesaert
Thank you guys..

16 August 2022, 07:25

Spanjaard
holly molly.... how do you keep those tiny pieces in place?? glue or soldered. amazing

16 August 2022, 07:41

Bart Goesaert
thank you Spanjaard, this has been glued.. everything is a bit to close to be able to solder. for the tiniest parts, I put the part on a knife, then apply some slow curing glue on the tip of the missile. drop the part in place. put it straight and fix with CA...

17 August 2022, 09:45

Matthew A
I'd be terrified of coughing and lossing the parts forever

17 August 2022, 12:42

Spanjaard
Thanks Bart. They look amazing

17 August 2022, 13:53

Bart Goesaert
@Matthew: spareparts are provided... and luckily a lot of extra's to compensate for the ping... and in summer during a heat wave... no need for sneezing

17 August 2022, 17:17

Spanjaard
good, because sneezing will probably not just send the small parts flying, but even the completed missiles 🙂

17 August 2022, 19:28

Spanjaard
Mine should be arriving this week, after seeing this beauty, I could not stop myself from ordering the Flanker. I have not yet but the courage to order the missiles from shelf oddity....

19 September 2022, 20:04

Bart Goesaert
Enjoy that one. It is a nice one. Put it aside for a bit to get a clear view again...

20 September 2022, 03:42

Project info

Su-27 Flanker B Ukrainian airforce

48 képek

1:144

Folyamatban

1:144 Su-27/Su-30 (Flanker) (Master AM-144-020)

1:144 Su-27 Flanker B Vacu Canopy (Brengun BRL144152)

1:144 Su-27 Flanker Cockpit (RetroWings RW44072)

1:144 Su-27/Su-30 (Shelf Oddity SO214427)

1:144 R-27T (AA-10 Alamo-B) (Shelf Oddity SO11449)

Összes album

Összes album megtekintése »