Yoshi 3D print
Commentaires
8 16 December 2021, 20:02
Robin (WhiteGlint)
3D printed Yoshi to gain some more experience with resin figures.
Especially with cleaning and (brush) painting.
Here my job cleaning was not the best one and I need to be more diligent in the future.
I had less problems with my Catapult.
As I don't want to work with lots of isopropyl alcohol I cleaned Yoshi in warm water with dish detergent.
Some varnish will hopefully solve my problems as this little guy still is a bit sticky, even after the paint has dried.
3D printed Yoshi to gain some more experience with resin figures.
Especially with cleaning and (brush) painting.
Here my job cleaning was not the best one and I need to be more diligent in the future.
I had less problems with my Catapult.
As I don't want to work with lots of isopropyl alcohol I cleaned Yoshi in warm water with dish detergent.
Some varnish will hopefully solve my problems as this little guy still is a bit sticky, even after the paint has dried.
16 December 2021, 20:24
Robin (WhiteGlint)
Yes, I use the Anycubic wash and Cure Station 2.0.
But even these tools need to be used right. 🤔
I think maybe I didn't clean good enough and did not cure long enough. Though curing too long should make the parts very brittle, I believe.
Yes, I use the Anycubic wash and Cure Station 2.0.
But even these tools need to be used right. 🤔
I think maybe I didn't clean good enough and did not cure long enough. Though curing too long should make the parts very brittle, I believe.
16 December 2021, 20:49
S M
Ok that's strange. Although I'm not an expert and I don't own any 3D printer. I have been dreaming of resin printer but my apartment is too small and I'm afraid of fumes. Maybe Santa will give me a garage some day...
Ok that's strange. Although I'm not an expert and I don't own any 3D printer. I have been dreaming of resin printer but my apartment is too small and I'm afraid of fumes. Maybe Santa will give me a garage some day...
17 December 2021, 16:59
Robin (WhiteGlint)
As I use the printer inside my house as well and I am not a fan of toxic fumes either, I use only plant-based resins which are not toxic.
But it still smells bad, especially when removing the cover from the printer after the print has finished. 😄
Using some protection like gloves and a mask is still very much recommended.
Working with plant-based resin may be an option for you.
The printer I am using is quite small too, so the parts I can print are not that large either. If you want I can provide you some pictures and measurements.
As I use the printer inside my house as well and I am not a fan of toxic fumes either, I use only plant-based resins which are not toxic.
But it still smells bad, especially when removing the cover from the printer after the print has finished. 😄
Using some protection like gloves and a mask is still very much recommended.
Working with plant-based resin may be an option for you.
The printer I am using is quite small too, so the parts I can print are not that large either. If you want I can provide you some pictures and measurements.
17 December 2021, 18:16
S M
Thanks! You can PM them to me. btw what is the source of that Yoshi's 3D-model?
Thanks! You can PM them to me. btw what is the source of that Yoshi's 3D-model?
17 December 2021, 22:56
Robin (WhiteGlint)
Yoshi's from Thingiverse.
thingiverse.com/thing:4788638
I'll write you a PM regarding the printer and so on.
Yoshi's from Thingiverse.
thingiverse.com/thing:4788638
I'll write you a PM regarding the printer and so on.
18 December 2021, 09:15
Album info
Cute little Yoshi from Nintendo to gain some experience with figure painting and to have an excuse to print some more stuff.