Ferrari F50

1
May 30, 2020
Front wheels. Photo-etched brake pads coloured with Sharpie permanent marker and sanded back with file in a circular motion to reveal metal and brake wear. Brake callipers painted with black Sharpie paint pen. Middle section painted with Sharpie metallic silver and gold pens. Not too happy about the pen strokes. Don't own any paints or brushes at this stage.
2
May 30, 2020
3
May 30, 2020
Front wheels and suspension. All done with Sharpie black paint pen and Sharpie gold and silver metallic pens.
4
May 30, 2020
Rear wheels and suspension. All done with Sharpie black paint pen and Sharpie gold and silver metallic pens. Still don't own any paints at this stage.
5
May 30, 2020
Went and bought some paints and brushes. Housing done with one coat of Tamiya acrylic flat black and then one coat of Tamiya enamel gun metal. Spider legs done with Sharpie black paint pen and detailed with Sharpie metallic gold and silver pens. Hobby Design photo-etched Ferrari logo superglued on.
6
May 30, 2020
Engine block done with Sharpie metallic silver pen followed by a thin enamel gun metal wash. Enamel paint was thinned with turps.
7
May 30, 2020
8
May 30, 2020
9
May 30, 2020
Photo-etched Ferrari logo superglued onto cylinder head.
10
May 30, 2020
Photo-etched Ferrari logo superglued onto cylinder head.
11
May 30, 2020
Sunvisers and wipers painted in three coats of Tamiya acrylic flat black. Handbrake painted in acrylic flat black with the handle painted in enamel gun metal. Roll bars painted in Tamiya enamel gun metal.
12
May 30, 2020
Steering wheel painted in three coats of Tamiya acrylic flat black with pin holes poked into the grips and bolts detailed with Sharpie metallic silver pen. The centre is coated in Tamiya smoke (clear black) to give it a gloss coating for the decal. I plan on coating this section with a clear flat coat once the decal has been placed.
13
May 30, 2020
Indicators/levers painted in three coats on Tamiya flat black. Gear shift coloured with Sharpie metallic silver pen and then coated in a Tamiya enamel gun metal wash to tone down the silver and give it more of a metal look.
14
May 30, 2020
Pedals coloured with Sharpie black paint pen and photo-etched parts superglued around the base. A little messy with the glue here.
15
May 30, 2020
Photo-etching wrapped on the back of the pedals levers.
16
May 30, 2020
Pedals coloured with Sharpie black paint pen and then sanded back to reveal metal while keeping the little holes black to represent the non-slip rubber.
17
May 30, 2020
Completed pedals. Photo-etched pedals superglued on.
18
May 30, 2020
Exhaust glued, but not yet painted.
19
May 30, 2020
Exhaust painted in an enamel gun metal wash and then detailed in a Tamiya X-16 (purple gloss) wash and Tamiya X-26 (clear orange). The enamel not having fully cured in some places mixed with the acrylic to create black/grey spots which I think adds to the overall effect.
20
May 30, 2020
21
May 30, 2020
22
May 30, 2020
23
May 30, 2020
24
May 30, 2020
Cooling fans painted in Tamiya acrylic flat black with the fans painted in Tamiya enamel gun metal and then fan brackets detailed with a black Sharpie permanent marker.
25
May 30, 2020
Photo-etched grills superglued to the back of the fans.
26
June 5, 2020
Photo-etched grill superglued to the front fan.
27
June 5, 2020
The instructions said to paint the cockpit in semi-gloss black, when the F50 is actually carbon fiber throughout. The decals provided only cover the centre console and the doors so I combined Tamiya silver chrome and black acrylics to create a carbon effect paint. I then added the centre console decal and coated everything with Tamiya smoke. The floor mats are the photo-etched pieces first coated in a metal gloss black paint and primer in one then a coat of Tamiya flat clear acrylic to bring back that rubber look and then superglued on top of the original molded mats.
28
June 5, 2020
Handbrake installed and knobs detailed with a toothpick. Gearbox to come. Seats to come. Seat backing colour matched with the dashboard, which I'll discuss more with that photo.
29
June 7, 2020
The dashboard. My Achilles heel. A part I thought would be easy has caused me nothing but drama. I started out painting the top air con fans and front strip with flat black. I then taped the centre and painted the rest in the recommended colour of 7 : 1 middle grey : purple. It was a horrible colour and it looked nothing like the real thing. It just wasn't going to cut it. I decided to mix my own colour of 6 : 8 : 2 neutral grey : purple : black and go over it again. Glad I did until I realised I'd gone over the fans on top and the paint seeped through the tape on the front. I ended up going back over them again with flat black, but it ended up on the grey part so I gave that another coat, but in doing so couldn't get a clean look without large brush strokes which got on the fans again. After this frustration I went over the fans with a fine tipped Sharpie along with the bleed on the front. I then went over the front in clear gloss for the decal to stick to, avoiding the fans and knobs as best as I could because I wanted to keep them looking flat. The speedometer decal ripped, but the front one went on okay. I wasn't happy with the colour of the front decal so I coated it in Tamiya smoke, but ruined the front fans in the process. The paint stripped and I had to go over them with the fine Shaprie. The grey ended up being way too glossy so I coated it in a clear flat and finished it off with the photoetched logo.
30
June 7, 2020
Another view of the dashboard with detailed knobs and buttons done using flat white and flat red acrylics and a toothpick.
31
June 12, 2020
Completed dashboard. Not too happy with how this turned out, but I guess it could have been worse. Put a clear coat on the speedometer to make it look less like a paper sticker.
32
May 30, 2020
Seats taped down the middle (this part will be painted red) and coated in three coats of Tamiya flat black. The instructions suggested to paint these parts in semi-gloss black, but I felt that the matt finish would look more like leather. I'm happy with the results. Seatbelt buckle detailed with Tamiya flat red.
33
June 7, 2020
Seats coated with Tamiya flat red. Unfortunately the black paint seeped through the taped area and was very hard to remove, so I attempted to cover it up. Eight coats later and I'm still seeing black through the red. I'm happy with the result considering, but sad that I lost a bit of detail in the process.
34
June 7, 2020
Photo-etched lumbar adjustments superglued onto the side of the seats.
35
June 7, 2020
Another view of the seats. You can see the carbon effect on the sides (and back) that I achieved by mixing flat black and silver chrome acrylics.
36
June 7, 2020
Photo-etched seatbelts, sprayed in gloss black paint and primer in one and then coated in a clear flat acrylic. Buckles sanded back to reveal original metal. These are way too short to put anywhere that makes sense so I'm now looking at possibly replacing them with seatbelt material and new buckles.
37
June 12, 2020
Completed doors. These were a pain to do. The decals ripped all over the place so I masked those areas with Tamiya gold leaf acrylic and a very thin brush and then coated the whole thing in a few coats of smoke to better match the real thing. The carbon fiber decals in the Tamiya set look nothing like the F50. I'm happy with the result. The photo doesn't do them justice.
38
June 8, 2020
Engine, exhaust, rear wheels and suspension cemented together. Just waiting on cabling to arrive in the mail for the next step.
39
June 8, 2020
40
June 8, 2020
41
June 12, 2020
Carbon fiber decals added and coated in Tamiya smoke. The middle section had additional layers of smoke to further darken the tint on that section as this closer to how the real thing looks. Photo-etched F50 logo, plates and pump nozzle superglued on. To my surprise the Hobby Design photoetched kit didn't come with this horse logo so I had to use the metal sticker decal from the Tamiya kit. Bolts painted on with Tamiya silver chrome and a pin.
42
June 8, 2020
Coated body parts in Tamiya grey primer. First time using primer. Didn't realise how dusty it would get. Regret using the box to spray as it just created a dust bowl.
43
June 8, 2020
First coat of primer after wet sanding with 800 grit. There were lots of rough surfaces that needed to be sanded back, most likely due to lack of technique and spray back. The section with the fuel pump lid actually snapped in half so is out of shot being cemented back together.
44
June 8, 2020
I sprayed a second coat primer using Tamiya white fine primer. This stuff goes on so differently to the grey primer. It is more paint-like and didn't leave as rough a surface. This is after another wet sand with 800 grit.
45
June 8, 2020
Some of the plastic was revealed again due to me missing a few sections of mold lines after the first coat... d'oh!
46
June 8, 2020
A second coat of fine white primer (third in total) and another wet sand with fine buffer pads/sticks. Looking good and feeling smooth. Ready for paint now... gulp! Parts are lightly placed together for the photo. No glue yet.
47
June 10, 2020
Black parts sprayed in Tamiya TS semi-gloss black. Two dry/mist coats and two wet coats. Came out so much better than expected. Such an even and smooth finish. Feeling proud. Unfortunately that part on the left snapped again so I will need to glue that back together again.
48
November 7, 2020
Bottom turned out perfect with the Tamiya lacquer spray, but then I tried putting a panel wash on it and it was ruined. I ended up having to remove the paint and redoing it with a brush and a mix of gloss and flat acrylic blacks because the can of spray ran out. Not happy, but I can live with it. Vents detailed with silver metallic sharpie and gunmetal enamel.
49
November 7, 2020
Body was painted in Tamiya TS-8. Came out great in some places and terrible in others. A lot of this was my lack of experience with a spray can. Touched up mistakes with some additional red lacquer paint and brushes. Can see some brush marks on the front, but it'll do for a first model.
50
November 7, 2020
Front bumper turned out terribly. Not sure why. Will be stripping this and redoing it.
51
November 7, 2020
52
November 7, 2020
53
November 7, 2020
This section snapped but will glue it back together later in the build due to its position in the model and the fragile section of the breakage.
54
November 7, 2020
Too much glue when sticking these pieces in. Was a shame as these parts were looking good.
55
November 7, 2020
This part was touched up with a brush and lacquer red, but some of the brush marks are visible.
56
November 7, 2020
Some drip marks on the underside of the spoiler.
57
November 7, 2020
Underside of this piece sprayed in semi gloss black lacquer and touched up with black lacquer and a brush. Not the best job I'll admit.
58
November 7, 2020
Seatbelts! Ended up ordering the Scale Production Gurtset Motorsport set.
59
November 7, 2020
You can see the issues I had with the door decals in this shot. Not looking forward to doing the decals on the wheel arches.
60
November 7, 2020
The manual said to paint the engine bay in chrome silver, but there was another modeller who used heat shrink instead and it looked really good. I had some insulation tape that looked very similar so gave it a go. Happy with the results.
61
November 7, 2020
Insulation tape used here too.
62
November 7, 2020
Had the metal photoetching and had planned on cutting out the clear plastic, but in attempting to cut the brittle plastic it snapped so I gave up and glued it back together. The inside is coloured chrome silver with a metallic sharpie.
63
November 7, 2020
Superglued the metal photoetching to the plastic piece.
64
November 7, 2020
Edges painted with black paint pen. Inside painted in flat black acrylic.
65
November 7, 2020
Back of rear light enclosures first painted in black and silver metallic to give the carbon look like the interior, but I mixed up gloss black with flat black. I think the result actually looks pretty good, despite not being accurate to the F50.
66
November 7, 2020
Combined a section of the metal photoetching to the plastic wiper as I felt this looked more like a real wiper.
67
November 7, 2020
Black panel liner added to wheels for a little more realism. Clear gloss acrylic brushed onto the tyre walls to look like tyre shine and create more contrast between the worn tread.
68
November 7, 2020
Tyres painted in a wash of white, rubber black and orange and then lightly sanded to give worn tyre look.
69
November 7, 2020
Close up of the engine detail. Those metal wires are guitar strings.
70
November 7, 2020
Hose and clamps added to engine.
71
November 7, 2020
72
November 7, 2020
Overall engine with hoses and clamps added. Waiting for distributor cables to arrive to complete this.
73
November 7, 2020
More insulation tape.
74
November 7, 2020
Panel lining added with Tamiya panel liner and black lacquer paint with a toothpick.
75
December 7, 2020
Original distributors were sanded down and removed.
76
December 7, 2020
New distributors and ignition wires were created using MFH detailing wire inserted into 1mm sections of hollowed out electrical wire.
77
December 7, 2020
Wires were then attached using superglue.
78
December 7, 2020
79
December 23, 2020
Engine bay competed
80
December 23, 2020
81
December 23, 2020
82
January 3, 2021
Water bottle made from thin cardboard, coated in white lacquer, dipped in an acrylic clear blue wash and weathered with Tamiya weathering set D.
83
January 3, 2021
Boot/trunk detailing complete. Battery and wiring is all after market. Bottles were made from scratch.
84
January 3, 2021
Tubing made from scratch with wire wound into a spring, covered in Teflon tape, painted in pva glue and painted in rubber black acrylic paint.
85
January 31, 2021
PE coloured and added to clam shell
86
January 3, 2021
Went back and chromed the gear stick with a Molotow liquid chrome marker.
87
January 3, 2021
Seemed a shame to have to hide all that detail in the boot... so I chopped the car in half. This way I can display the model with the boot open. A little touching up on the body to go now.
88
January 22, 2021
Clear coat done! 1 x mist coat + 2 x wet coat using Tamiya TS-13 spray
89
January 22, 2021
90
January 22, 2021
91
January 22, 2021
Engine in place! To say this was difficult is an understatement. PE detail added to wheel arch.
92
January 31, 2021
Headlights fitted and decals on
93
January 31, 2021
94
January 31, 2021
Custom number plate backing, made from styrene pill packaging and painted gloss black.
95
January 31, 2021
Looks much better than just the decal sticker on the red. Unfortunately the rear grill didn't slide all the way in.
96
January 31, 2021
Bumper glued to body with PE grill and lights fitted.
97
January 31, 2021
I have gone for a permanent engine display look by glueing two firm wires to each side of the boot, mimicking the actual hood props of the F50.
98
January 31, 2021
99
January 31, 2021
I'm going to leave the boot permanently open to display the after market detail I have added. Just need to glue it in place.
100
January 31, 2021
101
January 31, 2021
Bonnet glued in place and propped up with a pin while it dries.
102
January 31, 2021
COMPLETED!!
103
January 31, 2021
104
January 31, 2021
105
January 31, 2021
106
January 31, 2021
107
January 31, 2021
108
January 31, 2021
109
January 31, 2021
110
January 31, 2021
111
January 31, 2021
112
January 31, 2021
113
January 31, 2021
114
January 31, 2021
115
January 31, 2021

Commentaires

12 17 May 2020, 09:03

Peter Hardy
Welcome to Scalemates Pete! You'll meet the nicest people here! Any problems you have can be solved, just ask for help.

17 May 2020, 09:08

Peter Muldoon
Thanks Peter! 🙂

17 May 2020, 09:09

Martin Oostrom
Just use a different avatar than the other Pete. Still have nightmares from that one!
And welcome to the madhouse!

17 May 2020, 09:18

Peter Muldoon
Aww the other Pete ain't so bad lol. Thank you for the welcome.

17 May 2020, 09:42

Peter Hardy
Well that's pretty impressive for a first ever build Pete! I've never used Sharpies so that's a new one on me. Suspension is looking very nice! Keep up the good work mate!

18 May 2020, 07:42

Martin Oostrom
Looking pretty nice for a first build Peter. A bit lazy using sharpies instead of paints, but it might be I'm a bit jealous not thinking of it first 😉

18 May 2020, 09:05

Kerry COX
I hear that your a new kid in town, and being a newbie, I say welcome to Scale mates and all it's perils. 😉 👍
You picked a difficult but nice kit to begin with. 👍
From what you have posted, you look to have a better grasp than some of us 'seasoned' contenders.
I will be looking forward to more of your work images, as the bits you have posted seem to have had a great deal of care taken. 🙂
well done and enjoy your stay. 👍 🙂

18 May 2020, 18:13

Peter Muldoon
Thank you for the kind welcome everyone! The sharpies are handy and after seeing a couple of videos of people using them I thought I'd give it a go since I already had them at home. The control on them is great, but the consistency is a little thick for large parts which makes it very difficult not to leave stroke marks. I absolutely love the look of them on smaller parts like small joints, rings, nuts, bolts, etc. I finally gave in and bought some Tamiya paints and brushes yesterday so I will post some more photos soon.

19 May 2020, 00:30

Peter Hardy
Remember when colouring in to stay inside the lines!

19 May 2020, 02:36

Peter Hardy
Wow! The interior is coming together very well. Nice work on the suspension too. The engine is going to look fantastic! You're doing good! Keep it up!

27 May 2020, 11:58

Kerry COX
The detailing work is exceptional. 👍
I really liked what you did with the clutch, brake and throttle pedals. 👍
Is Peter leaning over your shoulder with this build. ? 😉
The painting of exhaust system will be interesting to see, as the heat discolouration was pretty intense. 👍 😉
Most impressed. 👍

27 May 2020, 20:17

Martin Oostrom
Why don't I believe this is a first ever build? Like Peter and Kerry I'm impressed. You're a worthy addition to this nuthouse 👍

28 May 2020, 10:30

Spanjaard
welcome to SCM PeTeR23. nice looking Ferrari so far 🙂

28 May 2020, 11:04

Peter Muldoon
Thanks guys! I've definitely fired a few questions Peter's way and Google is getting the workout of its life. Kerry, I just uploaded the finished pedals and will be doing the exhaust soon. I have been trying out a few techniques on the sprues for the exhaust discolouration and am looking forward to doing it. I like detailing with the brushes and my paint collection has been growing daily. I'd be lying if I said I wasn't procrastinating on the body spray a little, but I'll get there soon enough. Thoroughly enjoying this!

29 May 2020, 04:42

Spanjaard
it seems the album is gone now.... 🙁

29 May 2020, 13:25

Peter Muldoon
Hmm, seems they were somehow deleted. Not sure what happened there. Have uploaded them all again now.

30 May 2020, 02:40

Peter Hardy
Nothing there!

30 May 2020, 08:27

Peter Muldoon
They should be there now. The photos were deleted from the album and then uploaded to a new album. Very annoying. Let me know if you still can't see them and I'll see what else I can do.

30 May 2020, 09:42

Peter Hardy
Nope not there. Need to tell Tim the admin.

30 May 2020, 10:08

Peter Muldoon
Okay, I think I got it this time!

30 May 2020, 11:33

scalemates
👍 restored

31 May 2020, 11:56

Peter Hardy
Thanks Tim!

31 May 2020, 23:22

Peter Hardy
Outstanding PeTeR! Good to see you are testing techniques and not limiting yourself! This is going to be something to be proud of!

31 May 2020, 23:25

Peter Muldoon
Thank you Tim 🙂

6 June 2020, 12:43

Rafael Lang
going very well! I'm in!

8 June 2020, 04:40

Peter Hardy
Strewth! You sure you've never built a model before? Ok, dash is a disaster, lessons learned, next one will be a triumph! Love the seats but you will need to get some panel liner to do a 'pin wash' which will bring up details. Don't forget to apply a clear coat first though. Bloody impressed Pete, so much for my "all glue and fingerprints" prediction! What do I know?

14 June 2020, 03:08

Chaz Gordon
For future reference, tamiya acrylics are fairly easy to strip if you feel the need to start over. If fresh, they'll come off pretty easily with some isopropyl alcohol (if you can find any at the moment) else, soak the part in brake fluid for 30 minutes, then a couple of minutes in thick bleach, rinse under the tap and give it a quick scrub to get any bleach out of the grooves. Hey presto, clean plastic. The same process will strip the chrome off of chromed parts too, but thats probably a big step right now.

Welcome to SCM and to the hobby.

One other tip, Acryllics and Enamels often dont play well together, and clearcoating the finished piece with tamiya gloss spray varnish might cause some reactions as it is quite high in solvents. So always do a test first, grab a random plastic item, and combine the paints on it you plan to use. Allow a couple of days for it to cure, then try varnishing it, see what happens. The same goes for decals, always try a test run with a spare decal any time you use a new varnish brand or finish.

14 June 2020, 04:12

Peter Muldoon
Haha, thanks Peter. I can assure you there have been a lot of "all glue and fingerprints" moments throughout the process. A pin wash on the seats would look great. As you mentioned to me the other day, the fans could also do with a wash. Thanks for the tips Chaz. I'm trying to keep to the lacquer -> enamel -> acrylic rule as much as possible. I am currently Googling panel liners and washes. Seen a few videos. I'm wondering if I could get away with a thinned out Tamiya Smoke or flat black acrylic for pin wash on the seats. Would lay down a clear coat first for sure. The metal fans would have to be enamel though right? I may end up purchasing a bottle of Tamiya Panel Line Accent for that.

For the body (doors/panels) I was planning on using the liner as well as a thin marker similar to those Gundam pens. I've seen people use them before the primer, during the primer and after the colour coats so I am a little confused as to when I should be adding mine given that I am spraying the body with the Tamiya TS sprays and not an acrylic or enamel through an airbrush. I've already laid down my primer coats so if it's meant to happen before then I may have missed the boat. Putting panel lining on a painted model seems daunting though. I would hate for the enamel thinner to eat through to the lacquer finish. Maybe a clear coat over the body would help with this? But then would that have to be acrylic or can it be the TS clear spray? Then there are acrylic panel liners!! *Screams*

16 June 2020, 00:58

Peter Hardy
Pin washes go on last Pete.

16 June 2020, 01:57

Chaz Gordon
Peter M, it's a mine field to be sure. Metallics can be done with Acrylics too, unless you are looking for a real metal mirror finish like Alclads. And that is generally only Airbrushed. If you just want a silver or steel finish on small parts, you can't go much wrong with the Vallejo model air metallics (even for brushing) which are water based and easy to work with. They are also a bit cheaper than Tamiya and you don't get all the nasty build up around the rim as it's in a dropper bottle.

Lacquers, I definitely recommend the water based Varnish offerings such as Vallejo and Alclad Aqua, water based will not react with much underneath as long as it's fully cured (Including decals etc). Anything solvent or alcohol based runs a risk of interactions, sometimes even with same brand/range paints, it's about the chemistry of how a Lacquer differs from a Varnish

Lacquer actually melts the layers underneath, sometime right down to the plastic, and if all goes according to plan, creates a chemically bonded single entity consisting of plastic, paint and gloss (or matt) surface. Varnish acts more like a clear paint, and should be impervious to water once cured, but may be prone to damage by alcohols or solvents depending on the chemistry of the Varnish. (It's also easier to strip off and start again if it all goes wrong)

I've actually had Tamiya spray Lacquers soften Automotive spray primers to the point you could get the well cured primer colour rub off on your hand while the lacquer was wet.

16 June 2020, 16:40

Spanjaard
you can do panel lines with flory model washes, they are clay and water, usually, interact with nothing. easy to apply, easy to remove if you have to.... great stuff. i chose them after a turpentine wash reacted with the unprotected plastic of my NXR and almost kill the build completely

17 June 2020, 00:26

Peter Muldoon
Peter, okay cool I'll just try to be careful with it. Chaz, that info on the lacquers is really helpful and something I had been wondering a lot about. Spanjaard, I saw a video with those clay washes and thought it was a really cool way of doing it. Time to go shopping I think!

On a side note, my seatbelts and tubing arrived today so I can start to work on that too!

17 June 2020, 13:08

Peter Hardy
You are a lost cause on your first build Pete!

18 June 2020, 07:00

Peter Hardy
Well Pete, you are certainly learning some techniques and lessons. How to do and what not to do. We have all broken thin parts and there are some things you can do to make the joins disappear. Overall I would be pretty pleased if I were you with your progress and the knowledge gained. With the brush marks sanding will even things out but you will have to polish to bring back the even surface. Clear coat will give you a shine and headaches! 800 grit might be a bit rough for a finished surface even if wet sanding. We might spend a little time together over a Jameson's at Xmas. Your Jameson's of course. Mine is too precious! Martin OOoooooooooostrom may have some words of wisdom to.

7 November 2020, 11:10

Martin Oostrom
Words of wisdom: Don't pee into the wind. Preferably drink your father in law's Jameson.

To even out the brush marks, use some very fine sanding cloths. Start at 3600 grit and work your way up to the finer grit. Don't apply too much pressure, let the cloth do the work and be very gentle around edges and raised parts.
After the gloss coat, start over with the cloths and finish with a polish.

When done, you'll have a VERY well executed first build. Something to be very proud of. As an added bonus, some mistakes made and lessons learned. Get used to the last part, as that will continue to happen 😄

7 November 2020, 11:28

Peter Muldoon
Thanks! Feeling good about it overall. Learning so much. I'm looking forward to applying what I've learnt to the next model.

Peter, I'll trade you a Jameson for a wet sand and clear coat!😉

7 November 2020, 15:04

Martin Oostrom
You did a really good job on your first build. Went overboard detailing the car. Some areas to improve, but that's part of the game.
Very Impressive Peter. 👍

1 February 2021, 20:01

Spanjaard
very nice indeed!

1 February 2021, 20:40

Rafael Lang
veey good! enjoy your builds, is just what I can talk to you, dont worry, is knowledge now! 😄

1 February 2021, 22:19

Brandon H
Looks great!!

1 February 2021, 22:43

Peter Muldoon
Thanks guys! Definitely a lot of mistakes here and a lot of lessons learnt. I figured I'd put as much detail into this one as possible and make all the mistakes on my first build. Hopefully that means there are less on the second build, although I know that's never guaranteed haha. I'm having lots of fun and loving the hobby. The stash it starting to build too! 😄

2 February 2021, 05:11

Peter Hardy
Ha ha ha! Mistakes will follow you like a shark! As a reward for such a great effort on the first build I have two kits here for you.

4 February 2021, 11:33

Chaz Gordon
Very nice finished article. I do love the detail level with Tamiya 1/24.

5 February 2021, 21:29

Album info

Tamiya Ferrari F50 1:24
Colour: Red

Ferrari F50

115 images

1:24

Terminé

Tous les albums

Voir tous les albums »