Arado Ar-190

1
March 14, 2020
Side gun bulge sanded down and trench filled. Also filled the trenched under the canopy as they aren't in the book
2
March 14, 2020
Raised panel lines removed and rescribed
3
March 14, 2020
Started adding photo-etch to floats after removing moulded detail
4
March 14, 2020
Completed floats
5
March 14, 2020
Rear of floats showing new photo-etch rudders
6
March 14, 2020
Float assembly primed
7
March 14, 2020
Engine and propeller built and painted
8
March 20, 2020
Engine weathers and glued into the replacement cowl. Propeller added to finish the sub-assembly
9
March 15, 2020
Photo-etch cockpit parts added - very fiddly work!
10
March 20, 2020
Cockpit painted and (maybe over-) weathered
11
April 5, 2021
Fuselage glued together and wings added. This shot shows the radiator section hollowed out and some mesh added so you can't see through it.
12
April 5, 2021
Float glued on - a lot of filling and sanding required. Floats already painted as the tops will be hard to get to.
13
April 5, 2021
Top view - still some work needed in the cockpit (rear seat and the framing between the two seats)
14
April 5, 2021
Side view showing the extension needed on the front of the fuselage as the after-market engine cowl wouldn't fit without it.
15
September 18, 2021
The aircraft in the book has a different canopy setup to the kit. I removed the centre upright and made a mould and a copy out of clear resin
16
September 18, 2021
Finished the interior and glued on the canopy pieces
17
September 20, 2021
Etched aerials added, canopy masked and framework painted
18
September 22, 2021
Main paint done - decals next
19
September 22, 2021
And about time to attach the nose and engine...
20
October 2, 2021
Decals added. Lots of small white markings that don't show up well in the photo, as well as the insignia from Blue Rider - I went for the EFRS markings from the English language version of the book
21
April 25, 2022
22
April 25, 2022
23
April 25, 2022
24
April 25, 2022
25
April 25, 2022
26
April 25, 2022
27
April 25, 2022
28
April 25, 2022

Kommentit

31 14 March 2020, 13:08

Dave Flitton
Wow - I like the attention to detail here. Awesome work

5 April 2021, 02:36

Greg Baker
Why wasn't I informed of this project being under way?! Luckily, I scan Uwe's wall every so often to snoop on what he's up to. I've been thinking about this one as well. Great to have a step-by-step guide along the way.

8 April 2021, 13:54

Cuajete
Following.

8 April 2021, 18:52

Uwe Kaeding
Thanks guys - started this one this time last year, so it's been moving slowly! Of course just after I started it special hobby released a new kit, so I probably could have saved the rescribing - but it was a good learning experience. Still some way to go on this though, including some changes to the canopy glazing.

9 April 2021, 06:42

Matthew A
Nearly missed this

4 May 2021, 19:16

Cuajete
Very nice job so far. Fantastic detail in engine.

4 May 2021, 19:46

Uwe Kaeding
Thanks Matthew & Cuajete. Really must get back to this one...

5 May 2021, 07:58

Alec K
Following. Special Hobby has a new Ar 196??? Or were you thinking about the Sword kit?

19 September 2021, 14:29

Uwe Kaeding
Thanks Alec - you're right, I must have been thinking of the Sword kit (I knew it was eastern European and started with S!)

19 September 2021, 22:38

Alec K
NP. Got me excited there for a minute. The Sword kit is apparently a bear to build, so the old Heller kit is still pretty good, raised panels and all.

20 September 2021, 01:39

Uwe Kaeding
Well there you go - newer isn't always better! Might be a good thing I stuck with the Revell kit, particularly as I'm building a comic book representation anyway...

20 September 2021, 01:51

Greg Baker
That was my reasoning… it even kept me from rescribing the panel lines. 😉

I can't wait to see what Uwe's going to come up with here.

20 September 2021, 04:26

Uwe Kaeding
Nearing the end, Greg - a bit more masking and then the final paint

20 September 2021, 04:51

Torsten
Nice build, I hold it for the same build in 1:32, follow with great interest 👍

2 October 2021, 06:15

Uwe Kaeding
Thanks Torsten. Finally got around to finishing this one (the rigging on the floats held me up) and taking the final photos.

25 April 2022, 02:31

Łukasz Gliński
Lovely! But why have you left the cowling and prop unpainted? 😉 😛

25 April 2022, 07:24

Uwe Kaeding
Thanks Lukasz - always good when the cowling and prop boss only need to be grey! The propeller blades have been painted though 😉. Unfortunately I had to paint them because the kit plastic was a different shade of grey to the resin cowling!

25 April 2022, 12:55

Cuajete
Very nice. Congrats!

25 April 2022, 17:27

Erik De Smet
This Tintin project needs the formal approval of master Greg Baker

25 April 2022, 18:03

Greg Baker
Ha! I've been stealing Uwe's Tintin build secrets for years!

27 April 2022, 05:58

Album info

This is the EFSR (European Foundation for Scientific Research) Ar-190 floatplane from the Tintin book The Shooting Star. Its based on the Revell 172 kit with an Eduard photo-etch set and a Quickboost cowling. As it is meant to be a civillian aircraft I've also tried to demilitarise it by getting rid of hard points and guns.

The Shooting Star

28 kuvien

1:72

valmistunut

1:72 AR 196 - Correct Cowling (Quickboost QB 72 395)

1:72 The Aircraft of Tintin - Part 4 (Blue Rider CD-005)

Kaikki albumit

Näytä kaikki albumit »