Terminator TundraZobrazit: Prezentace Mozaika Seznam 1February 20, 2020 2February 20, 2020 3February 20, 2020 4February 20, 2020 5February 25, 2020Housing for the 30mm guns.. 6February 25, 2020just replaced the handles, not really a necessity 7February 25, 2020Construction far from complete, but despite the sidewalls being composed of a lot of parts (4-6 each side...) 8February 25, 2020dryfit is.... perfect 9February 25, 2020really perfect... 10March 19, 2020a new brand for an attempt to make the slat-armor 11March 19, 2020The jig is a great help... 12March 19, 2020and first one ready 13March 19, 2020second one to... due to it being slanted, it didn't fit in the jig, but it worked... 14March 25, 2020still a lot to solder... 15March 25, 2020these buggers almost got the best of me, but finally I succeeded... 16March 25, 2020only the spacerbars to add 17March 28, 2020parts for 1 off the headlights.... 18March 28, 2020 19March 28, 2020for the final pieces of the slat-armor, I've found that apply a little bit of solder to the connection points worked best. 20March 28, 2020the last one... 21March 28, 2020still moveable... on to the coneection points to the frame... 22March 30, 2020copper rod from a coil is insulated, so after burning this away you have a black rod. This clearcoat prevents easy soldering 23March 30, 2020which is easy to clean up 24March 30, 2020ready to use, just applied tin and flux 25March 30, 2020to make the hinges for the slat-armor, just present the wire through the holes 26March 30, 2020add a little flux to the soldering points 27March 30, 2020prepare some tine bits of solder 28March 30, 2020present them to the soldering points to 29March 30, 2020and just heat it up for a short time... 30March 30, 2020then cut off the excess... fully workable hinge... 31March 30, 2020support brackets for the slat armor 32March 30, 2020and drivers/gunners hatches have some spaced armor to 33April 13, 2020started removing the originale casted slat armor, to be honest, it doesn't really need replacement 34April 13, 2020All removed 35April 13, 2020and fits like a glove 36April 13, 2020Tried mounting the brackets first, and then the upper pieces... very fiddly and unsatisfying. So the top is soldered as one piece, bottom parts still loose 37April 13, 2020and on the model... 38April 13, 2020added some wire to the scope 39April 13, 2020overall view 40April 13, 2020then the TOW-hook holders 41April 13, 2020and all armor into place... ready for paint... 42January 3, 2021First paint with AK... Too pale 43January 3, 2021Much better IMHO 44January 3, 2021Started the masking 45January 3, 2021Filling the voids 46January 3, 2021Unpacking, only one small area that needs attention 47January 3, 2021Testfit to extend the contours to the next surfaces 48January 3, 2021Testfit to extend the contours to the next surfaces 49January 4, 2021 50January 4, 2021 51January 4, 2021 52January 4, 2021 53January 4, 2021 54January 5, 2021Test fit so far... this side looks ok 55January 7, 2021And removed 56January 5, 2021This side has some discrepancies 57January 5, 2021 58January 7, 2021 59January 7, 2021Turret also done 60January 7, 2021Turret also done 61January 7, 2021Again some blutack 62January 7, 2021 63January 7, 2021 64January 7, 2021 65January 7, 2021 66January 19, 2021Rear slat armor mounted 67January 19, 2021Missiles too 68January 19, 2021 69January 19, 2021 70January 19, 2021 Komentáře23 December 2024, 09:01 - Project infoModern Russian150 obrázky1:72Probíhá1+Všechna albaZobrazit všechna alba »